Special Features

Canopy Boxed-In CS Roof Eave Gutter w FSP Soffit

NOTES: *

See isometric detail for installation of pigtail mastic ** Provide air gap of 1/4" min. at bottom of panel to avoid corrosion. *** Purlin is a typical example. See Canopy Framing drawings for required number of purlin rows.

CANOPY CS ROOF PANEL

TAPE MASTIC AT PANEL LAP

1/4-14 X 1 1/4" WT (6" C.C.)

PIGTAIL TAPE MASTIC (Install a "Pig Tail" down the bearing leg of panel to form a continuous line of tape mastic with panel lap and closure.)

1/4-14 X 7/8" WT (6" C.C.)

CS INSIDE CLOSURE

BL

1"

X'-X"

EAVE MEMBER

#12-14 X 1 1/4" (6" C.C. for CS PANEL) (12" C.C. for AP PANEL) HEIGHT CHANGE ANGLE (A-20-B) WALL PANEL (TYP.) (2) #12-14 X 1 1/4" (GA) ( 36" C.C.)

TRIM CAP (TC)

CANOPY FASCIA PANEL

1/4-14 X 7/8" WT (12" C.C.) HEIGHT CHANGE TRIM (LHTC) INSIDE CLOSURE ***CANOPY ROOF PURLIN OUTSIDE CLOSURE (2" X 3')

1 2 "

1

EAVE GUTTER

1/4-14 X 1 1/4" WT(6" C.C.) (TYP.) INSIDE CLOSURE

TAPE MASTIC ON TOP OF CLOSURE

CANOPY FASCIA PANEL CEE SOFFIT PURLIN #12-14 X 1 1/4" (TYP.) (6" C.C. for CS PANEL) (12" C.C. for AP PANEL) EAVE GUTTER (EGA) 1/4-14 X 7/8" WT (6" C.C.) (1) 1/4-14 X 7/8" (TRIM COLOR) GUTTER STRAP (GS) (_____ C.C.) * INSIDE CLOSURE w/ TAPE MASTIC TOP AND BOTTOM 1/4-14 X 7/8" (12" C.C.) TRIM CAP (TC)

TAPE MASTIC ON BOTTOM OF CLOSURE

** 1 4 "

(2) 1/4-14 X 7/8" WT

8 11

16 "

CS INSIDE CLOSURE

CANOPY CS ROOF PANEL

4"

PIGTAIL TAPE MASTIC INSTALLATION WITH EAVE GUTTER AT CANOPY

HEIGHT CHANGE GIRT

9"

(2) 1/4-14 X 1 1/4" WT (1 EACH SIDE OF HI-RIB)

2 ROWS DOUBLE BEAD MASTIC TOP & BOTTOM OF OUTSIDE CLOSURE

EAVE STRUT

HEADER #12-14 X 1 1/4" (12" C.C.) (TYP.)

** 1 4 "

XXX'-X"

XXX'-X"

***SOFFIT PURLIN

SOFFIT PANELING CAP TRIM (SSCT) JAMB TRIM(JT) 1/8" X 3/8" BLIND RIVETS (12" C.C.)

1/4-14 X 7/8" (EACH RIB) (SOFFIT COLOR)

SOFFIT TRIM (VPST)

#12-14 X 1" PANCAKE HEAD (12" C.C.) (TYP.)

1/8" X 3/8" BLIND RIVETS (12" C.C.)

FSP SOFFIT PANEL

DRAFTING NOTE: · 26 GA FSP soffit must always have 1/4-14 x 7/8" fasteners located at ribs at end supports. Change fasteners to "DIM" layer.