Composite Material, Rigid Board, R-Seal

AP Window by Chief Rigid Wall

AP Panel - Rigid Board Insulation in Wall - Window by Chief

Head Trim (HTT) lapped 4 1/4" min. past edge of door jamb. Flush with end of Jamb Trim (JTA).

Installation Steps: 1. Install Wrap Plate, if applicable. 2. Liner Cover Trim(LCT), if applicable. Use with Liner/Backer. Refer to Liner or Partition Panel Drawings. 3. Window with Bulbtite 4. Special Sill Jamb Trim (SPT) and Special Wrap Trim (SPT). 5. Rigid Continuous Insulation. 6. Header Trim (HTT).

INSIDE CLOSURE

Optional urethane caulk at HTT end. (NOT BY CHIEF)

HEADER TRIM (HTT)

2 1/4" X 1/4" PANEL NOTCH

SHEETING SUPPORT (SSP)

JAMB TRIM (JTA) WALL PANEL

7. Sheeting Support (SSP) 8. Notch and slit wall panel. 9. Place wall panel over trims with foam inside closure full width of header and sill. 10.Jamb Trim (JTA)

2" PANEL SLIT

2" X 1/4" NOTCH

2" SLIT

LINER COVER TRIMS

Notes: ·

SPECIAL WRAP TRIM (SPT-x)

#12-14 X ____"

Special Fastener =

Optional urethane caulk at panel slit and notch. Caulk under JTA. (NOT BY CHIEF)

·

Rigid Continuous Insulation thickness =

X"

· Rigid Continuous Insulation and vapor retarder are not by Chief. · Insulation is representative. Erector shall refer to insulation manufacturer’s installation information for further details/direction. The erector is responsible for providing the final solution for installation, air tightness, and performance of the liner insulation system. · The details shown below are typical. · Not all details may apply. · Specific details for additional features will be provided for complete installation instructions. · Drill Ø1/8" holes for Blind Rivets. · Rivets spaced at 7'-0" C.C. are temporary fasteners.

For best weathertightness performance, JTA/SSP and Head Trim assembly should land in flat of panel. Layout, verify, and consider field locating framed opening as necessary. If this condition cannot be achieved, special field trim modifications, and/or additional urethane caulking Not By Chief may be required.

Optional Urethane sealant at JT end (NOT BY CHIEF)

EDGE OF WINDOW JAMB FLAT OF HEAD TRIM

END OF JAMB TRIM (JTA)

4 1/4" TO EDGE OF WINDOW JAMB

WALL PANEL SLIT

Optional urethane caulk behind special sill jamb trim (NOT BY CHIEF)

JAMB TRIM (JTA)

SPECIAL SILL JAMB TRIM (SPT-x) NOTCH AND SLIT WALL PANEL FOR EXTENSION OF TRIM. (TYP.) ** SPECIAL FASTENER (12" C.C.) (TYP.) WALL PANEL

Optional Urethane caulk around 2" panel slit and under JTA (NOT BY CHIEF) (TYP.)

TRIM DETAIL AT CORNERS (Window not Shown)

BL

#12-14 X 1" PANCAKE HEAD (36" C.C.) (TYP.)

1/8" X 3/8" BLIND RIVET, (18" C.C.) WITH LINER COVER TRIM (LCT) JAMB

ZEE GIRT

OPENING WIDTH

SPECIAL FASTENER (12" C.C.) #12-14 X 1" PANCAKE HEAD (12" C.C.) 1/8" X 3/8" BLIND RIVET (7'-0" C.C.)

SPECIAL PLATE. REFER TO FRAMING PLANS FOR PIECE MARK (PL)

LINER COVER TRIM (LCT1) (AS REQUIRED) (LINER COLOR) LINER COVER TRIM (LCT2) (AS REQUIRED) (LINER COLOR)

1/8" X 3/8" BLIND RIVET (7'-0" C.C.) (TYP.) 3/16" BULBTITE RIVET (12" C.C.) (SIDE ONLY)

INSIDE CLOSURE

CEE HEADER

SPECIAL FASTENER (12" C.C.)

* Provide air gap of 1/4" min. at bottom of panel to avoid corrosion.

* 1 4 "

1/8" X 3/8" BLIND RIVET, (18" C.C.) WITH LINER COVER TRIM (LCT)

WINDOW BY CHIEF

#12-14 X 1" PANCAKE HEAD (12" C.C.)

HEADER TRIM (HTT)

SPECIAL WRAP TRIM (SPT-x)

BL

URETHANE CAULK (NOT BY CHIEF)

LINER COVER TRIM (LCT1) (AS REQUIRED) (LINER COLOR)

URETHANE CAULK (NOT BY CHIEF) Optional urethane caulk behind special wrap trim (NOT BY CHIEF)

WINDOW BY CHIEF

LINER COVER TRIM (LCT2) (AS REQUIRED) (LINER COLOR) URETHANE CAULK (NOT BY CHIEF) SPECIAL SILL JAMB TRIM (SPT-x)

OPENING

RIGID CONTINUOUS INSULATION (NOT BY CHIEF) SHEETING SUPPORT (SSP) WALL PANEL 1/4-14 X 7/8" (12" C.C.) JAMB TRIM (JTA)

SPECIAL WRAP TRIM (SPT-x)

1/4-14 X 7/8" (12" C.C.) CUT RIB AS NEEDED

1/8" X 3/8" BLIND RIVET, (18" C.C.) WITH LINER COVER TRIM (LCT)

GIRT/SILL

INSIDE CLOSURE SPECIAL FASTENER (12" C.C.)

Optional urethane caulk behind special sill jamb trim (NOT BY CHIEF)

#12-14 X 1" PANCAKE HEAD (12" C.C.)

RIGID CONTINUOUS INSULATION (NOT BY CHIEF)

WALL PANEL (TYP.)

CHIEF WINDOW HEADER AND SILL

FRAMED OPENING DETAILS AT JAMB