Composite Material, Rigid Board, R-Seal

First page Previous page 68 Next page Last page

CS Metal Bldg Walkdoor-PA-SF Rigid Wall

CS Panel - Rigid Board Insulation in Wall - Metal Building Walkdoor - Pre-Assembled (by Chief) or Self-Framing Not by Chief Refer to Order Documents for Doors by Chief

Installation Steps: 1. Install Wrap Plate. 2. Special Insulation Cover Trim (SPT). 3. Rigid Continuous Insulation. 4. Door. 5. Jamb Trim (JT) with notch at header. 6. Header Trim (HTT). 7. Notch and slit wall panel. 8. Place wall panel over trims with foam inside closure. 9. Cover Trim (COT). 10. Liner Cover Trim (LCT), if applicable. 11. Use with Liner/Backer. 12. Refer to Liner or Partition Panel Drawings.

Head Trim (HTT) lapped 3" min. past flat of Jamb Trim (JT). Flush with Cover Trim (COT).

2" JAMB TRIM NOTCH

2" X 1/4" PANEL NOTCH

HEADER TRIM (HTT)

Optional Urethane caulk around 1" panel slit and under COT (NOT BY CHIEF) (TYP.)

1" PANEL SLIT

1" SLIT

2" X 1/4" NOTCH

INSIDE CLOSURE

2" JAMB TRIM NOTCH

Notes: ·

Special Fastener =

#12-14 X ____"

JAMB TRIM (JT)

For best weathertightness performance, JT/COT and Head Trim assembly should land in flat of panel. Layout, verify, and consider field locating framed opening as necessary. If this condition cannot be achieved, special field trim modifications, omitting COT trim, and/or additional urethane caulking Not By Chief may be required.

Rigid Continuous Insulation thickness =

· Rigid Continuous Insulation and vapor retarder are not by Chief. · Insulation is representative. Erector shall refer to insulation manufacturer’s installation information for further details/direction. The erector is responsible for providing the final solution for installation, air tightness, and performance of the liner insulation system. · The details shown are typical. · Not all details may apply. · Specific details for additional features will be provided for complete installation instructions. · Drill Ø1/8" holes for Blind Rivets. · Rivets spaced at 7'-0" C.C. are temporary fasteners. · LCT1 or LCT2 used with Liner/Backer. Refer to Liner or Partition Panel Dwg. · Provide air gap of 1/4" min. at bottom of panel to avoid corrosion.

FLAT OF JAMB TRIM FLAT OF HEAD TRIM

SPECIAL TRIM (SPT-x)

WALL PANEL SLIT

DOOR FRAME

COVER TRIM (COT)

TRIM DETAIL AT CORNERS

LINER COVER TRIM (LCT1 OR LCT2) (Field modify as req'd) 1/8" X 3/8" BLIND RIVET (7'-0" C.C.) (TYP.)

RIGID CONTINUOUS INSULATION (NOT BY CHIEF)

OPENING WIDTH

#12-14 X 1" PANCAKE HEAD FASTENER (36" C.C.)

WALL PANEL

JAMB

SPECIAL FASTENER (6" C.C.) INSIDE CLOSURE #12-14 X 1" PANCAKE (7'-0" C.C.)

NOMINAL DOOR OPENING

ZEE GIRT

#12-14 X 1" PANCAKE HEAD (12" C.C.)

RIGID CONTINUOUS INSULATION (NOT BY CHIEF) #12-14 X 1" PANCAKE HEAD (12" C.C.)

1/8" X 3/8" BLIND RIVET (3'-0" C.C.) TYP. SPECIAL PLATE. REFER TO FRAMING PLANS FOR PIECE MARK (PL)

DOOR FRAME

HEADER TRIM (HTT)

SPECIAL TRIM (SPT-x)

1/8" X 3/8" BLIND RIVET (7'-0" C.C.) SPECIAL TRIM (SPT-x)

* Provide air gap of 1/4" min. at bottom of panel to avoid corrosion.

JAMB TRIM (JT)

* 1 4 "

LINER COVER TRIM (LCT1 OR LCT2) (Field modify as req'd)

CUT RIB AS NEEDED

JAMB TRIM (JT)

RIGID CONTINUOUS INSULATION (NOT BY CHIEF)

1/8" X 3/8" BLIND RIVET (7'-0" C.C.)

2 " MIN.

DOOR FRAME

CUT RIB AS NEEDED

WALL PANEL SPECIAL FASTENER (12" C.C.) COVER TRIM (COT) 1/8" X 3/8" BLIND RIVET (18" C.C.)

1/8" X 3/8" BLIND RIVET (7'-0" C.C.) SPECIAL TRIM (SPT-x)

WALL PANEL SPECIAL FASTENER (12" C.C.) COVER TRIM (COT) 1/8" X 3/8" BLIND RIVET (18" C.C.)

***1/8"-3/4"

***1 3/4"-2"

OPENING HEIGHT

NOMINAL

*** Locate JT/COT/HTT trim assembly to cover door frame avoiding interference with latch, door and hinges.

*** Locate JT/COT/HTT trim assembly to so cover trim COT aligns on minor rib. Adjust header widths accordingly.

DOOR OPENING

WALKDOOR HEADER TRIM DETAILS

WALKDOOR JAMB TRIM DETAILS

ALTERNATE WALKDOOR JAMB TRIM DETAILS (Alternate detail for increased door swing clearance)

CEE HEADER

Made with FlippingBook Annual report maker